Get 15% off your order with coupon code: SKILL15

BUILDABLES WEIGHING MACHINE

A1- Disassemble your Weighing Machine till Task 3. Refer to the Checkpoint given on page 17 (Build video - 04:10) to make sure the mechanism works smoothly. Further, check the Smart Solutions section on page 25 (How to use video - 01:12) before going ahead with Task 4.

If the problem persists, please fill out the Support form and we will get back to you shortly!

A2- Disassemble your Weighing Machine till Task 3. Refer to Step 13 of Task 3 on page 16 (Build video - 04:02). Make sure the white arrow on the sticker faces down when the machine is at the maximum height. If not, remove the sticker, pull the upper surface of the machine machine to the maximum height and reattach the sticker with the arrow facing down.

If the problem persists, please fill out the Support form and we will get back to you shortly!

BULDABLES SKETCHING MACHINE

A1- The above stated issue will not arise if the X-axis is used only till the 12 cm mark. In case the canvas goes beyond the 12cm mark, this issue arises due to the slight bent in the wooden sheet. Please refer to the Smart Solutions section on page 27 (How to use video - 00:20) and follow the instructions carefully to rectify your machine.

If the problem persists, please fill out the Support form and we will get back to you shortly!

A2- While inserting the Y-Axis/X-axis knobs, adjust (rotate) the piece on top with the arrow to make sure the gears interlock with each other as shown on page 21 and 23. If you are stuck at Step 11 of Task 5 (page 21/Build video - 06:24), please use a hook to attach the blue bands.

If you are facing a problem in any other step, please fill out the Support form and we will get back to you shortly!

BUILDABLES COMPOUND MICROSCOPE

A1- The Middle Lens Holder falls when the foam washers in the snaps are not able to hold the weight of the module. To stop this from happening, revisit the Checkpoint given in Task 2 on page 20 (Build video - 04:08) and follow the steps carefully. While inserting the snap back with the extra foam washer, make sure to push it all the way in.

If the problem persists, please fill out the Support form and we will get back to you shortly!

A2- Please clean the lenses thoroughly before starting with the solution given below. Make sure the lenses are flat on the wooden piece as shown on page 8 and 15.

Follow the instructions given in the How to Use section on page 42 (How to use video - 00:08) very carefully. There are 3 tasks that need to be done to get a detailed microscopic image:

1. Ensure that there is sufficient light reaching the lenses from the bottom. You can either use a phone torch or redirect sunlight with the help of the mirror module.

2. Position the middle lens holder EXACTLY at the position shown on page 43 (How to use video - 00:30).

3. Place the cloth specimen in the centre of the stage. Keep viewing from the top while you adjust the gear knob until you find the best position for the stage, where the image seen is detailed and focused. For a better experience, keep mobile on top with the camera on while you adjust the position of the stage.

If the problem persists, please fill out the Support form and we will get back to you shortly!

BUILDABLES SPY GLASSES

A1- While assembling, slightly stretch the part to fix it at every point. Don’t worry about breaking it, it is designed to expand. If it does break, use the extra part provided!

A2- To see 3D images, make sure to put blue lens on right eye and red lens on left eye, as mentioned in the How to Use section on Page 35 (How to use video - 00:31).

A3- The 3D Spy Glasses have been designed to fit an 8 or 9 year old. However, if the glasses are too tight, follow the instructions given in the Smart Solution section on page 37 (How to use video - 00:50).

The goal is to give your child an opportunity to build and explore the world of 3D and secret messages! You can also disassemble the 3D Spy Glasses till Task 3 and hold your glasses up to explore!

If you have another question, please fill out the Support form and we will get back to you shortly!

BUILDABLES SPIN ART MACHINE

A1- This problem arises mainly in the canvas gear as the wooden part is very big for the snap to hold. To prevent this from happening, make sure there is no pressure on the canvas other than from the marker on top. Push the canvas from top while pushing the snap from the bottom to fix it in place. You can use a fresh snap in case the snap one gets loose overtime.

If the problem persists, please fill out the Support form and we will get back to you shortly!

A1- Make sure you have followed all the Checkpoints given in the Build manual (or instructional video). If at any time the gears get detached from each other, check if the snaps are in position and push them back in from both sides.

SUPPORT FORM